Timpano TPT-1000.4 4x 260W RMS at 2-Ohm Class D Amplifier, 20Hz - 26kH 4-Channel

Timpano TPT-1000.4 4x 260 Watts RMS at 2 Ohms - Class D Amplifier - 20Hz to 26kHz - Four Channel

• COMPACT DESIGN: Digital class D Brazilian technology allows this amplifier to have a small footprint by integrating a high-speed mosfet power supply with top of line transistors to ensure performance in a small heat sink without compromising performance. Dimensions: 8.11″ depth x 8.11″ width x 2.60″ height

• POWER: This amplifier is designed to run your stereo system with the power it needs to perform! 1200 Watts maximum dynamic RMS power output of 4x 300 Watts at 2 Ohms per channel. Its high efficiency rate of 84% provides more power with less battery consumption.

• BRIDGEABLE: Double the power output to your speakers by bridging two channels. Minimum impedance of 4 Ohms per bridged channel at output power of 2 x 520 Watts RMS

• TECHNOLOGY: A smart electronic 2-way protection circuit protects the amp if it gets too hot or if speakers fail causing a short! Focusing in sound quality, a full range response of 20 to 26,000Hz was used to give the best sound reproduction on this tiny amplifier.

• FEATURES: Fork terminal connector power and speaker wire Inputs. Built-in crossover filters for easy tuning! Choose between a fixed HPF at 90Hz or LPF at 90Hz or just turn it FLAT and use your external crossover or DSP settings. It also includes Variable Gain Control. Level controls are not for adjusting volume. They adjust the amount of signal that is coming into the amplifier from your signal source.

Additional Information:

• Number of Channels: 4
  

• Max Dynamic Output: 4 x 300 Watts RMS 2 Ohms
  

• RMS Power at 2 Ohms 12.6 Volts: 4x 225 Watts RMS
  

• RMS Power at 4 Ohms 12.6 Volts: 4x 140 Watts RMS
  

• Bridged RMS Power at 4 Ohms 12.6 Volts: 2x 450 Watts RMS
  

• Supply Voltage: 11 ~ 16V
  

• Frequency Response: 20Hz ~ 26KHz
  

• Crossover Low Pass: Fixed at 90Hz
  

• Crossover High Pass: Fixed at 90Hz
  

• Signal to Noise: > 90 dB
  

• Harmonic Distortion: < 0.9 % THD
  

• Input Sensitivity: 0.2 V
  

• Input Impedance: 14K Ohms
  

• Impedance Output: 2 Ohms
  

• Consumption with Signal Musical: 4A ~ 50A
  

• Dimensions (L x W x H): 8.11” x 8.11” x 2.60”
  

• Weight: 3.75 Lbs

Before Installing:

You must follow the instructions for the product’s installation and connections to guarantee optimal performance. If you have any questions, get in touch with us. Before using the amplifier, always follow these guidelines:

• Make sure the amplifier is switched off before adding or removing any connections. This prevents possible damage to the equipment connected to the amplifier;
• Keep all cables as far away as possible from the ignition cables, electronic injection modules and starter switch since they may cause noise interference;
• Always use 100% Cooper cables and good quality connectors. This guarantees the sound’s quality and fidelity;
• To avoid damaging the cables, make sure that they do not touch sharp metal edges.Important: Use a 60A fuse 12 inches away from the battery as a safety precaution

The power rated data are based on equipment from the PRV Audio Group laboratory. Frequency reference of 1Khz with THD+N to ≤10% in impedances referring to the indicated in each measurement. The electronic components and the manufacturing process can present manufacturing variations, thus leading to a variation in the measurements made. This amplifier is designed to perform on music applications ( with speakers ), any load test ( resistant load ) is not recommended.

Key Features

• Number of Channels: 4

• Max Dynamic Output: 4 x 300 Watts RMS 2 Ohms

• RMS Power at 2 Ohm 14.4 Volts: 4x 260 Watts RMS

• RMS Power at 4 Ohm 14.4 Volts: 4x 165 Watts RMS

• Bridged RMS Power at 4 Ohms 14.4 Volts: 2x 520 Watts RMS

• Frequency Response: 20Hz ~ 26KHz

• Dimensions (L x W x H): 8.11” x 8.11” x 2.60”

• Weight: 3.75 Lbs